Table of Contents
A Liftmaster garage door opener’s most fundamental feature is the keypad.
The keypad has a series of passcodes that homeowners can create to access the garage door securely.
Because of this, we will teach you how to perform Liftmaster Keypad Programming in two ways – with and without the enter button.
In this way, you’ll know how to do it if you find yourself needing to do this in the future.
Tips in Choosing a PIN Code
Before we head on to the actual steps, let’s discuss first how to choose a new PIN code for your opener.
The first rule is to always choose a code that you won’t forget, or else it will be frustrating to keep resetting your code every time you forget it.
For this reason, always choose a code that you and your family will easily remember.
When choosing a PIN that is easy to remember, avoid using obvious codes such as 1234 or 0000.
You also have to avoid PINs with birthdays, postcode phone numbers, or even your address.
Change it immediately once you believe that a stranger has access to your passcode.
It’s best to do it to avoid break-ins and danger to your family in the future.
Also, use random combinations to make it difficult for intruders to guess it.
How To Program Your Liftmaster Keypad Without an Enter Button
It gives you an overview of programming a Liftmaster keypad without an enter button; follow the steps below:
Step 1: Turn Off The Opener
Before programming, you need to disconnect the garage door opener from the power source.
This is to get into the process seamlessly without the risk of mistakes and accidents.
Step 2: Detach the Faceplate
After, remove the faceplate and look for the operating switch or the dual program.
Step 3: Switch to Operating Mode
Upon switching on the dual program, it will automatically set to operating mode.
Then, switch it over to change it into program mode.
This program mode will help you change your pin code.
Step 4: Change the Code
In this step, enter the code you want.
Make sure that it is easy to memorize to avoid forgetting it.
After, switch the program back to operating mode.
Then, plug the opener, and the PIN code should reset.
Turn on the garage door opener and test if the code works.
If it doesn’t work, you’re good to go.
On the other hand, you can repeat the steps above until the new code works.
However, if you’re having a hard time, you can reach out to Washington’s Garage Doors – a reputable garage door company, to assist you with resetting the code.
How To Program Your Liftmaster Keypad With an Enter Button
If your Liftmaster garage door opener has an enter button, follow the steps below:
Step 1: Look for the Learn Button
If your Liftmaster opener has wall control, use this.
Otherwise, use the learn button if your garage door lacks a wall control feature.
This means you need to use a ladder to reach your garage door opener.
Once you have access to the opener, press and release the learn button.
On the other hand, do this step twice if the model of your opener has a MyQ control panel.
After, you can now proceed to changing or entering a new code.
Step 2: Register a New Code
When entering a new code, you need to enter a four-digit number within 20 seconds.
Then, press the enter button.
Ensure the code you enter is something you can easily remember.
Step 3: Lights Begins to Blink
It may be different for Liftmaster garage openers, but most lights will blink after entering a new code.
The lights indicate that the new PIN code is registered successfully.
Step 4: Test the New Code
Wait for 10 seconds and test if your new code works.
If the opener doesn’t work with the new code, repeat the steps thoroughly.
On the other hand, you can reach out to a garage door repair service to assist you in changing the code.
Call Washington’s Garage Doors to assist you!
Need Help?
We hope you find success in following our steps in Liftmaster Keypad Programming.
However, there are times that reprogramming won’t be successful.
In this case, reach out to Washington’s Garage Doors to help you change the PIN code of your opener.
